PRODUCTS

+
  • polymer-melt-index-tester_1527494.jpg

Polymer Melt Index Tester


The JH-450T Polymer Melt Index Tester is mainly used for the analysis and research of the melt flow rate of thermoplastics under certain conditions. The melt flow rate (melt index) of the thermoplastic refers to the mass of the plastic passing through the standard die every 10 minutes under a certain temperature and load. It is expressed by the MFR (MI) value, which can distinguish the thermoplastic in the molten state The viscous flow characteristics. This test is of great significance to the quality assurance of thermoplastic and chemical fiber raw materials, products and other products. This instrument has a color touch screen, which is convenient and friendly to operate.
  • Products Detail
    • Commodity name: Polymer Melt Index Tester

    The JH-450T Polymer Melt Index Tester is mainly used for the analysis and research of the melt flow rate of thermoplastics under certain conditions. The melt flow rate (melt index) of the thermoplastic refers to the mass of the plastic passing through the standard die every 10 minutes under a certain temperature and load. It is expressed by the MFR (MI) value, which can distinguish the thermoplastic in the molten state The viscous flow characteristics. This test is of great significance to the quality assurance of thermoplastic and chemical fiber raw materials, products and other products. This instrument has a color touch screen, which is convenient and friendly to operate.

    Polymer Melt Index Tester

     

    The JH-450T Polymer Melt Index Tester is mainly used for the analysis and research of the melt flow rate of thermoplastics under certain conditions. The melt flow rate (melt index) of the thermoplastic refers to the mass of the plastic passing through the standard die every 10 minutes under a certain temperature and load. It is expressed by the MFR (MI) value, which can distinguish the thermoplastic in the molten state The viscous flow characteristics. This test is of great significance to the quality assurance of thermoplastic and chemical fiber raw materials, products and other products. This instrument has a color touch screen, which is convenient and friendly to operate.

     

    1.   Polymer Melt Index Tester  Introduction

     

    Shanghai Jiahang JH-450T Polymer Melt Index Tester is fully in line with ASTM D 1238 standard, and improved and upgraded to facilitate the test of high flow instant fat meter, especially suitable for the melt-blown material PP (polypropylene), polyethylene and other materials test.

    Meet the quality standards:

    ISO 1133-2011, ASTM D1238-13, GB/T 3682-2018, JJG878-1994 (2005), JB/T5456-2005

     

    2.   Polymer Melt Index Tester  Parameter

     

    model

    JH-450T

    advantage

    Can measure products with fast flow rate, with membrane plug

    Measurement methods

    Mass method

    Display method

    4.3 inch LCD color touch screen

    Timekeeping accuracy

    0.01S

    Cutting method

    Manual / Auto

    Measuring range

    (0.1-3000)g/10min

    Recovery Time

    ≤2min

    Result output

    Mini printer

    power supply

    220V,50HZ

    Extrusion part

    Inner diameter of discharge port (die)

    φ2.095±0.005mm

    Length of outlet (die)

    8.000±0.025mm

    Inner diameter of charging barrel

    φ9.550±0.007mm

    Length of charging barrel

    152mm

    Piston rod head diameter

    φ9.474±0.007mm

    Piston rod head length

    6.350±0.100mm

    Piston displacement indication error

    ±0.01mm

    Load part: the standard test force is eight grades, the relative error of the test load is≤0.5%, and the mirror plating standard is adopted

    Level 1

    0.325kg=(piston rod+weight tray+heat insulation sleeve+1 weight body)

    level 2

    1.200 kg=(0.325+0.875 weight No. 2)

    Level 3:

    2.160 kg=(0.325+No. 3 1.835 weight)

    level 4:

    3.800 kg=(0.325+No. 4 3.475 weight)

    Level 5:

    5.000 kg=(0.325+No. 5 4.675 weight)

    Level 6:

    10.000 kg = (0.325 + No. 5 4.675 weight + No. 6 5.000 weight)

    Level 7:

    12.500 kg = (0.325 + No. 5 4.675 weight + No. 6 5.000 + No. 7 2.500 weight)

    Level 8:

    21.600 kg=(0.325+No.2 0.875+No.3 1.835+No.4 3.475+No.5 4.675+No.6 5.000+No.7 2.500+No.8 2.915 weights)

    Barrel temperature

    Barrel temperature range

    The temperature control point can be set arbitrarily within the range of 50.0℃~450.0℃

    Adopt intelligent PID adjustment

    Reach temperature control point and keep constant temperature in a short time

    Constant temperature accuracy

    ±0.2℃

    Temperature control gradient (℃):

    ≤±0.5℃(10mm above the die)

    Temperature resolution

    0.01℃

     

     

    3.   Polymer Melt Index Tester Feature And Application

     

    1. The equipment adopts PID intelligent temperature control with high temperature control accuracy, which can ensure that the temperature at the upper 10 mm of the inner die of the cylinder is within ±0.5℃.

    2. After packing, can quickly restore the constant temperature state

    3. Nitriding processing of key parts, high strength, hardness, small deformation characteristics and ensure the accuracy and stability of the measured data.

    4. The heating speed is fast, the instrument heater adopts special spring heating ring of hot runner, and its main material is imported nickel chromium wire alloy. Compared with the traditional heater, the dry burning ability is stronger, the power is higher, the heating uniformity is better, the service life is long, and the instrument can work for a long time at high temperature 450℃.

    5. The instrument is heated by voltage regulating module, which can adjust the voltage and power in a full range. Compared with the traditional solid-state relay on-off control, the heating is more stable and rapid, so that the constant temperature can be quickly restored after packing.

    6. The instrument adopts custom-made armored platinum resistance temperature sensor, the accuracy is the highest grade A, the accuracy is within 0.1℃, compared with the traditional sensor, has the characteristics of impact resistance, corrosion resistance, vibration resistance and can be bending at will, the service life is longer, can ensure the instrument in 450℃ the highest temperature environment for A long time.

     

    4.   Product Qualification

     

    Jiahang Polymer Melt Index Tester  has obtained CE certification, TART certification, ISO quality management system certification, more than 10 software copyrights and multiple patents to ensure that each instrument has stable performance and excellent quality.

     

    5.   Deliver,Shipping And Serving

     

    We have a top R&D team returned from Europe and America, cooperate with our superb manufacturing team, professional sales team and dedicated service team, working together to provide customers with high-tech, high-quality products and efficient, convenient, Comprehensive pre-sales and after-sales professional services.

     

    6. FAQ

     

    Q:How many years have your company made Polymer Melt Index Tester?     

    A:22 years of scientific instrument manufacturer, laboratory solution provider!

    Q:Which certificate do you have for your products?      

    A:Jiahang has obtained CE certification, TART certification, ISO quality management system certification, more than 10 software copyrights and multiple patents to ensure that each instrument has stable performance and excellent quality.

    Q:Will you will attend the fair to show your products?   

    A:Yes,Every year we will participate in some internationally renowned exhibitions to launch our new products,such as Arablab、PICCTON、Analytica Russia、Lab Africa、Analytica Germany、Analytica Latin America and so on,we are looking forward to your visit.

    Q:How about your company's R&D strength      

    A:Possess strong R&D technical capabilities (a R&D team of more than 20 people, with an average degree of doctorate degree, graduated from well-known universities at home and abroad, with an average work experience of 8 years), able to deal with and solve product-related technical problems

    Q:If OEM is acceptable?    

    A:Provide OEM customization service, product built-in software has autonomy, can customize development settings

    Q:Are you a trading company or a manufacturer?    

    A:100% manufacturer, no middlemen and distributors make the price difference, the price of the source factory is very advantageous; Jiahang is headquartered in Shanghai, China, has 15 service outlets and 2 production plants in China, and has sales in more than 10 countries overseas proxy.

    Q:How about your delivery time?

    A:"Generally, it will take 7 to 15 working days after receiving your advance payment. Depend on the quantity."

    Q:Which payment can be acceptable ?

    A:We could accept the payment by L/C, TF, Paypal , Western Union,etc.

    Q:Service 

    A:We could provide Online instruction ; Real-time support by video-ca or voice-chat.

    A:Any customer who cooperates for the first time promises to provide a production cost price trial opportunity to solve your worries about product quality problems.

    A:Provide official product quality assurance documents that comply with legal benefits to escort you with worry-free after-sales service.

Previous

Next

Previous

Next

Hot Products

Messages